By Plumbing Guide for Installing a Bathtub
By Plumbing Guide for Installing a Bathtub
Blog Article
What are your ideas regarding How to Install a Bathtub Yourself?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bath tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently accessible, the project can relocate quickly; if you have to open a wall surface to remove the old bathtub and also position the new tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will need a helper to vacate the old tub and embeded in the new one. Ensure you have actually qualified on your own for the work and are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will aid you set up a brand-new tub in your restroom if you have actually currently purchased a brand-new tub and don't require to change the plan of your previous water pipelines.
Your devices and also product list must comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be rather bothersome because of the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the faucet and the sink. Safeguard the faucet in position with the manufacturer provided backnut. When the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous kind must be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of both wood boards under its feet, position the bath tub in the called for position. The wood boards are handy in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level reviews degree.
To mount taps, fit all-time low of the furthest adaptable faucet adapter to the suitable supply pipeline by making a compression join; after that do the very same for the various other tap.
Switch on the water system and also examine all joints and new pipework for leaks and tighten them if required. Fill up the bathtub and also check the overflow outlet and the normal electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's instruction manual. Tiling and also sealing around the bathtub needs to wait until the bath tub has been used a minimum of when as this will certainly settle it into its last setting.
Planning for the Installation
To start with, the sustaining structure provided with the bath ought to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to avoid pressure on the tub.
Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with moisture as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can split relatively very early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily offered on the market. It is recommended to fit the tiles making use of water-resistant or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that piece of content was worthwhile. So long as you liked our blog entry please remember to share it. I praise you for your time. Visit again soon.
Best choice? Ring us! Report this page